TIPS ABOUT HOW TO Extend Smok Pen Recharge Time


TIPS ABOUT HOW TO Extend Smok Pen Recharge Time

The Smok Pen is a new pen that was created by two guys in California. They wanted to create a cool writing instrument that appeared as if a real pen but had the opportunity to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has had the market by storm.

smok pen

The Smok Pen has a built quality that’s just great. I came across that even though it can be an electronic pen the build quality is just as good as the pens that I have reviewed. Simply because of how they made the very best cap. You don’t have to be worried about the cap cracking or breaking on you Smok Valve Pen.

The two biggest differences that separate the Smok Valve from other pens is the form of the coils and just how that they are built. In general the coil on a Smok Pen is larger than on other pens. I think that they did this on purpose, to make the pen feel bigger.

If you take a look at a Smok Pen, you will observe that your body of the pen is round and not smooth like other pens. On the back of the pen there exists a little tab that houses the coil. Once you press on the tab it is simple to turn the heating element on and off. I must say i liked this feature since it allows me to utilize the Smok Pen 22 whenever Personally i think like smoking.

To utilize the Smok Pen it is advisable to keep the heat button pressed. After the button is pressed, the heating element will start to warm up. Once it reaches the appropriate temperature you can turn off the heating element. Smok recommends utilizing a 22mm tank. I prefer a more substantial tank, but that’s just me.

When you put your Smok Pen in to the tank you will see a indicator light seriously. The indicator light will remain green unless you put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is important to always put your pen into the charger before you apply the e-liquids to the coil heads. It is also important to do that before putting your e-liquids into the coil heads.

After you have completed this step, it is best to check to see should you be at the right temperature for the coils to fire. If not then you should turn the power off and try again. Should you be still not satisfied together with your Smok Pen i quickly suggest you take it set for some troubleshooting. This is what I would call the “troubleshooting process” because sometimes things just do not work as they should. It is suggested that you perform the next two steps, then go ahead and check the Smok Pen to see if it still has the electronic charging port.

Before you go any further you should take away the battery from your own pen and unscrew the magnetic cap. You need to then remove the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body which is green in color. You need to loosen this wire using pliers. After you have loosened this wire you can then access the sub-ohm. You need to then take away the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch the coils.

After you have placed the sub-ohm tank in to the pen you should then place the rest of the components including the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Start the energy and follow the on screen instructions. You need to place the pen’s battery in to the microwave and activate the setting. You should then wait approximately 30 seconds before EightVape turning it back off. When you first put the pen in to the microwave the electronic reading will show a minimal voltage protection setting. If this setting does not automatically get set you then should follow the on screen instructions.

Once the Smok Pen has already reached the temperature that it requires to reach you should then connect both wires to the positive and negative on the positive post on the Smok unit. You should then connect another end of the battery to the negative post on the negative side of the Smok unit. The final step is to connect the positive cable to underneath of the Smok’s on / off switch.

After all of the components have been placed in to the pen, you should turn the power on. Following the first test run, you need to be able to see the battery life indicator light seriously. If you don’t see any sign of life from the Smok Pen, you need to take away the battery from the pen and then replace it with a fresh one. For your convenience gleam green light that could be pressed so that you can confirm the battery charging status. When you have done these things and you also do not start to see the green light indicating charging, you should replace the battery.